You should always air a trailer tire up to the max cold psi rating. The 80 psi for cold is just for the tire being cold and wouldn't be the max psi once it actually heats up. Each tire brand/model is going to be different so you'd have to reach out to the manufacturer to find out the actual maximum psi instead of just the recommended/max cold psi that's written on the sidewall.
To put it in perspective, for every 10 degrees in temperature change you'll see a 1 psi change. If your tires... view full answer...
The Curt hitch part # C13704 does fit I-beam frames like your 2022 East to West Tandara 321RL-OK has but the frame has to be between 22 and 66 inches measured from outside to outside. So it could work for you and most likely does but you would want to measure your frame first. view full answer...
Hey Chris, going with a JTs Strongarm part # LC191025 will give you the best solution as it allows you to keep your expensive Ground Control stabilizer setup and also makes it much more stable.
To install the kit you will also need the part # LC314592. view full answer...
It appears your 2020 East to West Tandara 385MB uses the Lippert Ground Control 3.0 # LC675817 leveling system. If this is what you have we do have the Replacement Front Jack # LC362485 which attaches to the Motor # LC343758. Lippert does not offer the internal shaft or gears separately so you will need to replace the entire jack.
If you have a different landing gear system please let me know what you have. view full answer...
Hey Thomas, the side marker Furrion cameras are available as a pair with the part # FCE48TASL but they are not available individually. view full answer...
Our brake controllers are not fit guided for the trailers and instead are for the vehicle side. So if you have your East to West Della Terra info in our fitguide it wouldn't show a fit for it since brake controllers normally install on the vehicle side.
You didn't mention what happens if the brake pedal is pressed in your tow vehicle. Do the brakes work at all when this happens? NC would indicate no connection which in the case of a brake controller means that it can't detect the load... view full answer...
The correct SumoSprings Trailer Helper Springs for a Forest River Salem Hemisphere 273RL are part # TSS-107-40 for 3K-5K axles and part # SS26MV for 5K-8K. In order to find the right kit you simply need to look on the axle tag in the center of the beam for the capacity and then choose the kit that this capacity falls inline with. view full answer...
Hey Scott, thanks for reaching out!
What is the width of the slide out on your 2022 East to West Silver Lake 26KRB? This will be the outside flange to outside flange dimension (see attached). I want's able to find the width of your slide out online but if you can get me this dimension I'll let you know what will fit! view full answer...
The 132 inch height you mentioned for your 2021 East to West Alta 2800KBH is actually the height from the ground to the top of the trailer. For a cover, the height is measured from the undercarriage to the roof, which is why you are seeing a difference. So yes, the Adco cover you mentioned will fit:
- Adco SFS AquaShed Cover for Travel Trailer # 290-52246
The AquaShed # 290-52246 is a really nice option that is going to keep your trailer protected from the elements with its triple-layered... view full answer...
I would be happy to go over the suspension enhancement options for your 2020 East to West Silver Lakes Travel Trailer with Tandem 3500lb Dexter axles, but the MORryde Premium Rubber Suspension Kit for Tandem Axle Trailer # MR97ZR you were looking at only works with 5200-7000lb axles.
Since your equalizers measure 5-3/4" center to center of the horizontal mounting holes you can use the Dexter E-Z Flex Equalizers # K71-654-00 as a replacement. These equalizers have rubber cores to absorb... view full answer...
We have two possible shock kits for a 2022 East to West Alta 2850KRL, the Roadmaster Comfort Ride Shock Absorbers part # RM-2460 and Lippert Bolt-On Shock Kit part # LC281281. These both attach a bit differently so I recommend looking over how each attaches via the attached instructions and choosing the one that best fits your needs. The shocks don't interface with the equalizers so there will be no issues there. The 4,400 lb axles use a 5,200 lb beam with a 3,500 lb spindle and since the... view full answer...
The only available ST235/85R16 we offer with an F load range rating is the Karrier ST235/85R16 Radial Trailer Tire part # AM10501. This tire has an 81 mph speed rating with five year warranty. It is rated for up to 3,960 lbs. Unfortunately, I cannot recommend switching to a lower load range rating than what is listed/installed on the trailer from the manufacturer. view full answer...
While I can not look at what exact parts are installed on your 2021 East to West Alta 1900MMK travel trailer I was able to see images and videos where the LED Clearance or Side Marker Trailer Light # MCL0032RBB does appear to be the correct part. To verify this you will either need to contact the manufacturer with your VIN information or measure your current light. I have included an image below which shows the measurements for these lights. You will also want to check the wiring behind... view full answer...
While there is not a specific mount for carrying as spare tire on a 24x60 etrailer Cargo Carrier # e99049 I have seen several use a U-Bolt Mount # CE22007Z-11050-2 to mount around the base of the tray rack to secure the tire under the carrier. view full answer...
The " ***Error*** Feature Disabled " code on your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote # LC675817 can be caused by the following things:
1. Front of coach is below level when starting Auto Level process (only when trying to initiate Hitch Recognition). You'll need to raise front of coach above level and restart Auto Level process.
2. Touch pad power not cycled between consecutive leveling operations. You'll need to turn the touch pad off... view full answer...
I am sorry to say that we do not carry the vent cover you are looking for. The only cover we have from Dometic is the # DMC37FR which is made for a 23-3/8" long x 6-1/2" wide cutout. So this is not going to match what you have at all. At this point I believe your best bet will be to contact Dometic directly to see if they have a replacement available. view full answer...